Description
Features
Specifications

  DESCRIPTION:

Passive Devices "PDI-60CMS" is a synthesized, SAW filtered, 60dBmV high performance fixed frequency modulator. This unit is manufactured and thoroughly tested, to comply with and in most cases exceed, all FCC recommended parameters. The PDI-60CMS provides fixed channel selection for any cable channel from channel 2 through 134 (54-750MHz).

$895.00 per Unit - *Plus Shipping/ Handling
* Shipping amounts will vary, depending on size, weight & destination. ALL shipping charges will be invoiced AFTER the order has been processed.


FEATURES:  
+60dBmV RF output level
Please Indicate Desired Pre-Set Channel:
Quantity :
$895.00 PER UNIT
Frequency range: 54-750MHz plus sub frequencies channels T-7 through T-13
FCC offset factory set.
60dB spurious performance at full output Level.
Professional grade SAW vestigial sideband filter for true adjacent channel operation
Separate audio/video and composite IF loops
BTSC stereo compatible, encoded baseband or 4.5MHz audio Input.
HRC available
Brushed aluminum face plate
5 year warranty
UL Listed Canada/U.S.
ISO 9002 Certified
OPTIONS: Internal SAP Generator
OPTIONS: Internal Stereo Encoder
  SPECIFICATIONS:
 
RF SECTION
Output Frequency 2-134 (54-860MHz) plus sub frequencies T-7 through T-13
Output Level +60dBmV Typical (Peak Video Carrier)
Output Level Adjustment 20dB Range
Output Impedance 75ohms (Unbalanced)
Spurious Output
(@ +60dBmV Output with Aural Carrier 17dB Down)
At least 60dB Below Video Carrier
Broadband Noise
(@ +60dBmV Output)
>80dB Below Video Carrier
Frequency Stability ±5kHz Maximum (±2kHz Typical)
Vestigial Sideband Response -20dB at IF Channel Edge; -60dB a Adjacent Video and
Aural Carrier Frequencies and
VIDEO SECTION
Input Type Composite Video, Negative Sync
Input Level 0.5 Vp-p Min. for 87.5% Modulation
Frequency Response ±0.75dB (10Hz to 4.2MHz)
Differential Gain 3% Typical at 87.5% Mod. Depth
Differential Phase 3 Deg. Typical at 87.5% Mod.
Hum and Noise 60dB Min. at 87.5% Modulation
Tilt 1.1% Maximum on 60Hz, 50% Square Wave
Group Delay Response Meets FCC Predistortion Requirements forColor Transmission
AUDIO
Input Type Unbalanced (Balanced Optional)
Input Impedance 600ohms
Input Level 250mV Min. for 25kHz Peak Deviation
Frequency Response ±1dB (50Hz-15kHz)
FM Hum and Noise 0dB
Subcarrier Frequency 4.5MHz ±500Hz
Stereo Specifications
Frequency Responses 20Hz to 14kHz +dB
Separation >27dB (20Hz to 14kHz) Typical
Pilot Rejection 50dB
Signal to Noise Ratio 65dB, Overall Through Expander and Receiver
Audio Input Impedance 10K ohms
Nominal Input Level (APL) 0dBm, Adjustable + 10dB
Distortion 0.5% Maximum THD
OPERATIONAL
AC Line and Power 85 - 256 Vac, 60Hz, 25 Watts
High efficiency switching mode power supply
Operational Temperature Operational Temperature 0 to 50 degrees C
Rear Panel Connections
 
RF Output F Female
Video Input F Female
Audio Input Screw Terminal (stereo units RCA)
4.5MHz IF Input F Female
Front Panel Controls
RF Output Level Adjust
Aural Carrier Level Adjust
Video Modulation Depth Adjust
Audio FM Deviation Adjust (Disabled on stereo units)
Front Panel Indicators
Power On
Rear Panel Control
Baseband Stereo Switch (Pre-emphasis Defeat) (Disabled on stereo units)
4.5 Audio Switch